-40%
HUD Car Head Up Display Smart Digital Speedometer OBD2 Scanner Diagnostic Tool
$ 18.55
- Description
- Size Guide
Description
>>Description
Thanks for purchasing our OBD smart digital device.This product connects car OBD2 interface by OBD cable, and dispaly the driving datas, e.g. vehicle speed, engine RPM, water temperature, fuel consumption etc. It can keep the driver’s eyes always on road to avoid the dangerous of lowering down head to read the dashboard. This product won’t change any car ECU datas.
OBD smart digital device is equipped with a very powerful detection for error code, the device can display the error code information clearly in text form,and it can clear the fault information,and display accelerating competitive mode,brake performance test mode, read the entire vehicle data stream information,and the other functions.
Features:
1. Available for cars with OBD2 and EUOBD port Car automatic diagnosis system ,plug and play
2. TFT LCD multi color smart display
3. The first scan will show the vehicle protocol
4. The language can be changed
5. Multi function display mode or simple function display mode can be switched freely
6. Add new functions: accelerating competitive mode ,Brake performance test, can read the entire car data stream information
7. Rich Contents:vehicle speed,engine RPM,water temperature,voltage,instantaneous fuel consumption,average fuel consumption,driving distance measurement,driving time ,low voltage alarm,high water temperature alarm,over speed alarm, engine fault code alarm, eliminate the fault code,freely switch between kilometers&miles.
Technical Parameters:
Environment temperature: -40 + 80 degree
atmospheric pressure 86-106KPa
Relative Humidity: 10% -95%
environmental noise: ≤60dB A
Alarm sound level: ≥30dB A
Working voltage: 9V ~ 16Vdc 12Vdc / 400mA
Product size: 73 x 68 x 46 cm
Key Functions: Light sensor, OBD interface
Setting button functions:
1. Short press in: 1 switch the display mode; 2 confirm the menu after enter into the menu
2. Push left: 1 switch the left area functions; 2 change the function setting after enter into the menu
3. Push right: 1 switch the right area functions; 2 change the function setting after enter into the menu
4. Long press in: after enter into the menu and finish the setting, long press in for 5 seconds to keep and exit.
Push left/right to switch function: Below are function abbreviations
ECT-engine coolant temperature
VLT-Voltage
FUE-fuel consumption
RPM- Revolutions Per minute
ODO-odometer
TIM-single driving time
DIS-single driving distance
Factory set:
Press in the setting button to find the system setting,and then short press in the button to enter into the menu,at last,push right to switch to the factory set,and long press in to keep and exit.
Eliminate the fault code:
When the device scan the program successfully,long press in the the button to enter into the setting menu,then push right to switch to the troubleshooting and short press in,then find the eliminate the fault code function,long press in to finish.
Setting Mode:
Long press in to enter into the setting mode,push right to choose the menu,and short press in to confirm.Once finishing the setting,long press in to exit.
Setting functions:
in the menu mode,all the default value can be changed,push left is to decrease,push right is to increase
Language Set:Please choose your familiar language
Warning Tone:turn on/off the buzzer
Speed Alarm:the default value is 150(the default value can be changed,push left is to decrease,push right is to increase)
Coolant alarm:default value is 120°, it means this device will give alarm when Coolant temperature is over 120°
RPM alarm: default value is 6000 r, it means this device will give alarm when RPM over 6000 r
BAT Alarm:default value is 10.5V, it means this device will give alarm when battery voltage is lower than 10.5V
Speed Adjust:adjust the speed according to the dashboard,default value is 107%
Speed Offset:When the vehicle turns off,but the device speed is not 0, then adjust the device Speed Offset value, if the device speed shows 5KM/H, then change the device Speed Offset default value at 5
BAT Adjust:if the battery voltage is different with the vehicle,it can be adjusted.
Engine Size: the default value is 1.6 L, if the fuel consumption is much different with the dashboard,please change it as the Displacement size
Fuel adjust:default value is 100%,it can be adjusted
Change Color:choose the display color that you prefer
CWT Unit : default coolant temperature is °C,also can be changed to ℉
Speed unit:default is KM,can be changed to Mile
Sum distance:can make the total driving distance same as dashboard if the dashboard shows the sum distance is 30000Km,the user can make the device value at 30000KM
Power off time:default power off time is 10s,for Auto start and stop cars,please make the power off time to 180-240s
Sleep Voltage:default is off ,if the device can’t auto off,please adjust the voltage at 13.2V or higher
Factory set:short press in to do the factory set
OBD diagnose set
Scan DTCs:scan the ECU to check if there is the error code,and show the error details
Clean DTCs:switch to Clean the DTCs,short press in the button to finish the cleaning
Driving test
Speedup test:show the speed,distance,driving 400m takes time,driving 100m takes time
Brake Test:show the speed,brake distance and time
Data Stream
Show all the vehicle data stream
OBD smart digital device installation:
1.Know your vehicle brand,the OBD smart digital device work for cars with OBDII agreement or EU OBD agreement. Open the engine hood and find the sticker below it see the below picture 1 , if it has words like OBDII CERTIFIED, then it can be installed.
2.Find out the 16 pin diagnostic link see the below picture 2 of the vehicle and connect it well with OBDII connecting line.
Troubleshooting:
1. The screen without any display,and no power
Start the car engine;check if the OBD cable line is tight;please pull down the OBD cables more times to ensure;check if product power switch turns on. If still no display ,please change another car to test, analyze whether the car OBD diagnostic interface is good, if it is not good,please repair it and try again.
2. Only shows the car voltage and be automatic power off after 60 second when the device is with power
this product just available for cars with OBD2 agreement and EU-OBD agreement(European region: after 03 years, Other region:after 07 years)
This Products donnot support JOBD and OBDI and recommended test for another car.
3. Inaccurate Speed
a.First check the speed unit is correct or not, the speed unit including KM/H and MPH,please refer to the setting to switch the unit.
b.When the product is power on,long press in the button to enter into the menu option,and right push once switch to setting,then short press in the button to the menu,and right push the button switch to the speed adjust option. if the dashboard shows 100,and the device shows the 101,change the default value at 106%
4. Inaccurate Fuel consumption
Check your car displacement,and set the device same as your car if your car is 2.0L,then change the device value at 2.0L .The fuel consumption can be adjusted,but we don’t suggest to change it ,because all the datas are read from the car ECU directly.
5. RPM Alarm
Default alarm is 6000,please refer to the setting to change.
6. Over peed alarm
Default alarm is 150KM/H,please refer to the setting to change the value.
7. The device cannot auto power off
A.After vehicle turns off,the device still display the speed,switch the setting to Speed Offset,and adjust the value same as the device speed. if the device shows 5KM/H after the vehicle turns off,then change the speed offset at 5KM/H
B.After vehicel turns off,the device still display the RPM,switch the setting to sleep voltage,and make the value at 13.2V
8. Auto start and stop cars
Change the Power off time to 180s
9.Wrong operation lead to crashes
Do a factory set
10. Why it will cause the car dashboard fault code bright?
As Universal OBD device supports multiple communication modes, and generally each car only supports one kind of the communication protocol ,according to the protocol to pull up the unneeded pins by the pliers. when the vehicle turns on,unplug and OBD cable and re-plug again,it will display the protocol
Package including:
1 x HUD Car Head Up Display
1 x Anti Slip Pad
1 x OBD Cable
1 x User Manual
>>
Payment
We only accept payment through Paypal.
If you don't have Paypal account, please register.
Payment must be received within 7 days after auctions ended. Unpaid dispute will be filed to eBay
for the non payable bidders.
>>
Shipping
1. WORLDWIDE SHIPPING.
2. Orders processed within 24-48 hours of payment verification.
3. We only ship to confirmed PAYPAL addresses. Your PAYPAL address MUST MATCH your
Shipping address.
4. If you have not received your shipment within 30 days from payment, please contact us. We
will track the shipment and get back to you as soon as possible with a reply. Our goal is
customer satisfaction!
5. Due to stock status and time differences, we will choose to ship your item from our first
available warehouse for fast delivery.
>>
Return
1. Our warranty does not extend to any products that are physically damaged or that are not under
normal operating conditions as a result of misuse or improper installation on the buyer/user's part.
2. Defective products must be returned within 30 days from the RMA issuing date. For all return
products customers MUST contact us for the returning address.In all cases, buyers pay shipping
fees at their own cost to return products for exchange or refund. We will be responsible for
the postage of replacements. Refund will be made upon receipt of the returned item.